IPSC1

Beleuchtungscontroller / Blitzsteuerung

IPSC1

  • Schnittstelle: Ethernet
  • Anzahl Ausgangskanäle: 1
  • Blitzstrom: max. 20A @ 200V
  • Dauerstrom: je max. 2A @ 30V
  • optional konfektionierte Kabelsätze
Inquire about product →Datasheet as PDF →
Controller passend zur Betriebsart wählen

Bei 24-VDC-Ausführungen ist für den Dauerbetrieb kein Beleuchtungscontroller erforderlich. Ein Controller kann optional zur Helligkeitsregelung oder für besondere Schalt- und Blitzfunktionen eingesetzt werden. SC-Ausführungen benötigen einen geeigneten Beleuchtungscontroller oder eine Stromquelle mit Strombegrenzung.

Specifications

Technical Specifications

01

General technical and commercial data

Design & Mechanics

Housing
Black aluminum case
Weight
approx. 285 g

Supply & Output Power

Flash current
max. 20A @ 200V
Continuous current
max. 2A each @ 30V
Ambient Temperature
from -5 °C/+23°F up to +50 °C/+122°F
Versorgung
12 V – 24 V DC (min 11 V, max 26 V)
Compliance
CE, RoHS2

Channels, triggers & interfaces

Interface
Ethernet
Number of output channels
1
02

Electrical characteristics

Model-dependent characteristics

In narrow view, the table can be shifted sideways.

variantElectrical characteristicsMeasured values and classification
variantChannelsSupply VoltageOutput voltageContinuous current (output)max. pulse currentPower consumption
IPSC1112 V – 24 V DC (min 11 V, max 26 V)200 V (pulsed) 55 V (continuous)2A @ 30 V20A @ 200 VMax 3A @ 24 V (72 W)

Notes on the specifications table

IPSC1

Operating modes: Continuous operation, external trigger, internal trigger, software trigger, external switching operation

Maximum output voltage: 200 V (strobe operation) 55 V (continuous operation)

Maximum pulse current (depending on pulse duration): 20 A at 200 V

Maximum continuous current: 2 A at 30 V

Pulse duration: 1 µs – 1000 ms in steps of 1 µs

Maximum frequency with external trigger: 4,9 kHz

Maximum frequency with internal trigger / external switching operation: 997 Hz

Trigger input: 0 – 5 V or 0 – 24 V level, positive or negative edge (not optically isolated)

Interfaces: Ethernet (10BaseT)

Supply: 12 V – 24 V DC (min. 11 V, max. 26 V)

Power consumption: max. 3 A at 24 V (72 W)

Dimensions (H × W × L): 39 x 88 x 103 mm

03

Connection and PIN assignment

Phoenix Contact MSTB 2,5/3-ST-5,08 · Controller Supply

Controller supply · Phoenix Contact MSTB 2,5/3-ST-5,08

Connector drawing

Connector layout according to original manual

PINFarbeWire colorFunction
+––Power Supply +12 to 24V DC
-––Power GND
PE––Protective Earth

Terminal designations as per original; no additional numeric PIN numbers derived.

RJ45 · Ethernet · Configuration

Ethernet · Configuration · RJ45

Connector drawing

Connector layout according to original manual

PINFarbeWire colorFunction
1––TX+
2––TX-
3––RX+
6––RX-

The original lists these four contacts for Ethernet. Other contacts are not added as unassigned.

USB-B · USB · Configuration, if available

USB · Configuration, if available · USB-B

Connector drawing

USB-B pinout according to original manual

PINFarbeWire colorFunction
1––V+
2––D-
3––D+
4––V-

Applies exclusively to device versions with a USB interface. USB 1.x/2.0, cable type A to B; virtual serial COM port according to manual.

D-Sub 9-pin · RS232 · Configuration

RS232 · Configuration · D-Sub 9-pin

Connector drawing

Connector layout according to original manual

PINFarbeWire colorFunction
2––TxD on controller → RxD on PC
3––RxD at controller ← TxD at PC
5––GND
4 ↔ 6––Handshaking loop back
7 ↔ 8––Handshaking loop back
1, 9––Not connected

Note the controller side. In the original, the signal names of the PC side are also compared.

Deltron DT13W3 · IPSC1 · LED output

1-kanalig · IPSC1 · LED-Ausgang · Deltron DT13W3

Connector drawing

Model columns according to original manual

PINFarbeWire colorFunction
1––CH1-, Channel 1 -
2––Not assigned
3––Not assigned
4––Not assigned
5––Not assigned
6––Not assigned
7––Analog ID
8––Signal GND (for signals 7, 9 and 10)
9––Trigger Output Digital Signal, 3,3V LVTTL
10––Digital ID (1-wire EEPROM), 3,3V LVTTL
A1––12–24V DC je nach Versorgung, max. 0,5A für Lüfter
A2––Power GND
A3––V+, Common Output Voltage

Signal GND and Power GND are labeled separately. Original image contains three model columns; observe the appropriate column.

Phoenix Contact MSTB 2,5/2-ST-5,08 · IPSC1 · Trigger Input

1-kanalig · IPSC1 · Trigger-Eingang · Phoenix Contact MSTB 2,5/2-ST-5,08

Connector drawing

Model columns according to original manual

PINFarbeWire colorFunction
+––Trigger Channel 1 +
-––Common Trigger GND

HIGH: +3 to +24V DC; LOW: 0 to +0,5V DC; undefined: +0,5 to +3V DC. Common trigger ground; note terminal order in original image.

04

Dimensional drawing

Dimensional drawing IPSC1 – IPSC1
Dimensions in mm; values in square brackets in inches.
05

Operating instructions

To maintain the optimal operating temperature, mount the device on a metal surface. Heat generation depends on the set output parameters.

Do not disassemble the device; sensitive components as well as high voltages and loads can cause damage and health hazards.

Do not expose to rain or moisture. The device is not intended for wet environments. Handle with care and do not throw.

Operate only with a power supply and within the limits specified on the respective controller and in its documentation.

Never connect or disconnect LED lighting while the power output is active. Always turn off the controller before changing the lighting.

06

Connection and control

Connection and control

Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1
Connection and control – IPSC1

Product inquiry

IPSC1 check for your application

Briefly describe your Prüfaufgabe.

Product: IPSC1

PDF Datasheet · Version 4.0

Select datasheet

IPSC1

Scope of the Data Sheet

The datasheet opens in a new tab. You can save it there as a PDF.