I-CON

Beleuchtungscontroller / Blitzsteuerung

I-CON

  • nachrüstbare Helligkeitssteuerung für 24V-Beleuchtungen
  • Dimmen über Potentiometer und/oder Steuerspannung 0-10V
  • verschiedene Leistungsstufen bis 1,2A erhältlich
  • kompakte Bauform zum Einschleifen in die Zuleitung der Beleuchtung
Inquire about product →Datasheet as PDF →
Controller passend zur Betriebsart wählen

Bei 24-VDC-Ausführungen ist für den Dauerbetrieb kein Beleuchtungscontroller erforderlich. Ein Controller kann optional zur Helligkeitsregelung oder für besondere Schalt- und Blitzfunktionen eingesetzt werden. SC-Ausführungen benötigen einen geeigneten Beleuchtungscontroller oder eine Stromquelle mit Strombegrenzung.

Specifications

Technical Specifications

01

General technical and commercial data

Supply & Output Power

Connection
M8, 4-pin
Versorgung
24 VDC
Compliance
CE, RoHS
02

Electrical characteristics

Model-dependent characteristics

In narrow view, the table can be shifted sideways.

variantElectrical characteristics
variantSupply VoltageContinuous current (output)
S18-0004-300-24-M8424 VDCup to 300 mA
S18-0004-350-24-M8424 VDCup to 350 mA
S18-0004-500-24-M8424 VDCup to 500 mA
S18-0004-600-24-M8424 VDCup to 600 mA
S18-0004-700-24-M8424 VDCup to 700 mA
S18-0004-1000-24-M8424 VDCup to 1000 mA
S18-0004-1200-24-M8424 VDCup to 1200 mA

Notes on the specifications table

Brightness control via potentiometer and/or 0–10 V. Controller and illumination power supply require the same zero potential. The maximum load current depends on the selected version.

Pigtail: 10 cm; other lengths on request. Only connect devices when powered off.

03

Connection and PIN assignment

M8 Built-in connector / pigtail coupling 4-pin · I-CON · 0–10V brightness control · wire assignment

1-kanalig · I-CON · 0–10V Helligkeitssteuerung · Aderzuordnung · M8 Einbaustecker / Pigtail-Kupplung 4-polig

See table for Anschlussbelegung.

Wiring by wire colors according to original

PINFarbeWire colorFunction
Input brownbrownbrown+24V
Input whitewhitewhitenot connected (n.c.)
Input blackblackblack0–10V Helligkeitssteuerung
Input blueblueblue0V
Output brownbrownbrownLighting +
Output whitewhitewhitenot connected (n.c.)
Output blackblackblacknot connected (n.c.)
Output blueblueblueLighting -

Wiring by wire colors: The original does not state PIN numbers; these were not supplemented from a standard pinout. Analog signal and illumination supply must share the same ground potential. Disconnect power before plugging.

04

Dimensional drawing

Dimensional drawing I-CON – I-CON
05

Operating instructions

The I-CON allows for simple and fast dimming of 24VDC LED lights via an external potentiometer and/or via a control voltage 0-10V. The module is equipped with M8 plugs (4-pin) as standard and can be easily looped into the connection between the DC power supply and the lighting. The I-CON is available as standard in various power levels with load currents up to 1200mA. The load current of the I-CON should always be selected to be higher than the load current of the lighting used. The more precisely the load current of the lighting and that of the I-CON match, the larger the control range. If the control range is too large due to the deviation, we offer a specific adjustment to the lighting you use as an option. Note: The analog input signal (0-10V) must have the same zero potential as the lighting supply! The devices may only be plugged in when they are de-energized!

Product inquiry

I-CON check for your application

Briefly describe your Prüfaufgabe.

Product: I-CON

PDF Datasheet · Version 4.0

Select datasheet

I-CON

Scope of the Data Sheet

The datasheet opens in a new tab. You can save it there as a PDF.