MINI-DOME-100-NG

Dombeleuchtungen

MINI-DOME-100-NG

  • Außen-/Innendurchmesser: 123,7/68mm
  • kompakte, lichtstarke Domebeleuchtung
  • 8 Segmenten getrennt ansteuerbar
  • Objektivöffnung mit Wunschdurchmesser 12-36mm
  • Dauer-, Schalt- oder Blitzbetrieb

Variants:

Inquire about product →Datasheet as PDF →

Specifications

Technical Specifications

01

General technical and commercial data

Design & Mechanics

Outer/inner diameter
123,7/68mm
Housing
Anodized aluminum, high-quality plastic
LEDs
32

Operation & Connection

Ambient Temperature
max. 50 °C recommended
electrical protection class
III, safety extra-low voltage operation
Connection
M12 connector (12-pin) / M12 plug (12-pin)
Versorgung
24 VDC type SC-Typ: For use with a Beleuchtungscontroller, see operating modes section
Compliance
CE, RoHS
service life
The service life of LED lighting depends on many factors.
Service life explained in WikiLED →
02

Model-dependent characteristics

Preliminary information; confirm before use.

Model-dependent characteristics

In narrow view, the table can be shifted sideways.

variantCurrent and flash operationMeasured values and classification
Light colourWavelength / Color Temperaturenm / KBeam angleLED · °Current consumption24VDC type / max. Konstantstrom SC-TypApproximate valuesMax. pulse current24VDC type / SC-Typ
t < 1 ms
Duty Cycle 1:10
Depending on flash conditions
IrradianceW/m² at constant current
@ 0,01 m
Approximate values · Distance from bottom edge of housing
Electrical powerWRisk groupEN 62471
Red615 nm80°––––exempt group
white6.500 K80°220 mA gesamt / 28 mA je Segment8000 mA gesamt / 1000 mA je Segment140 W/m²6 Wexempt group
Infrared850 nm80°––––exempt group
Blue470 nm80°220 mA gesamt / 28 mA je Segment8000 mA gesamt / 1000 mA je Segment145 W/m²6 Wexempt group
Green525 nm80°––––exempt group

Notes on the specifications table

Additional light colors and versions from UV to infrared available upon request.

03

Connection and PIN assignment

M12 Connector 12-pin · 24VDC · 8-channel · common anode

Connector drawing

Front view of housing

PINFarbeWire colorFunction
12red-bluered-blue+ 24V
1brownbrown- Kanal 1 / Channel 1
2blueblue- Kanal 2 / Channel 2
3whitewhite- Kanal 3 / Channel 3
4greengreen- Kanal 4 / Channel 4
5pinkpink- Kanal 5 / Channel 5
6yellowyellow- Kanal 6 / Channel 6
7blackblack- Kanal 7 / Channel 7
8greygrey- Kanal 8 / Channel 8
04

Dimensional drawing

Dimensional drawing MINI-DOME-100-NG
Preliminary drawing according to source data sheet.
05

Operating instructions

Areas of application

This version is designed for continuous operation at 24VDC.

Operating modes

  • DC operation on a suitable power supply with 24VDC
  • switched operation on a suitable power supply via e.g. PLC, opto-relay
  • switched operation on a lighting controller (e.g. IPSC/HPSC or Gardasoft) in conjunction with a suitable power supply
  • brightness-controlled operation via lighting controller (IPSC/HPSC or Gardasoft) in conjunction with a suitable power supply

Flash operation

Flash operation via controller (e.g., IPSC/HPSC or Gardasoft) in conjunction with a suitable power supply. Depending on the lighting controller used and the maximum available output/flash voltage, the flash current in this combination can be increased by a maximum factor of 2 to 3 in order to remain within the permitted voltage range of the output/flash voltage of max. 50V.

Current limits

The maximum permissible currents for continuous and flash operation are also specified on the product label of the respective lighting.

Areas of application

This low-resistance version, optimized for flash operation, can also be used for switched, brightness-controlled, and continuous operation.

Required supply

One of the following power supplies is required for operation:

  • a lighting controller, e.g. from the IPSC/HPSC series, from Gefasoft or Gardasoft, or
  • a current source with current limiting.

Flash operation

Due to its low-resistance design, the SC version is particularly suitable for maximum current in flash operation. Compared to the 24-VDC types, output or flash voltages in the usual range up to a maximum of 50 V can be used.

As a result, the maximum flash current is typically significantly above the factor 2–3.

Current limits

The maximum permissible currents for continuous and flash operation are also specified on the product label of the respective lighting.

Product inquiry

MINI-DOME-100-NG check for your application

Briefly describe your Prüfaufgabe.

Product: MINI-DOME-100-NG

PDF Datasheet · Version 4.0

Select datasheet

MINI-DOME-100-NG

Scope of the Data Sheet

The datasheet opens in a new tab. You can save it there as a PDF.