HPSC2

Beleuchtungscontroller / Blitzsteuerung

HPSC2

  • Schnittstelle: Ethernet
  • Anzahl Ausgangskanäle: 2
  • Blitzstrom/Kanal: maximal 40 A je Kanal bei 48 V
  • Dauerstrom/Kanal: 4 A je Kanal bei 24 V; maximal 5 A insgesamt
  • Pulsweite: 1µs bis 60s (Auflösung 1µs)
Inquire about product →Datasheet as PDF →
Controller passend zur Betriebsart wählen

Bei 24-VDC-Ausführungen ist für den Dauerbetrieb kein Beleuchtungscontroller erforderlich. Ein Controller kann optional zur Helligkeitsregelung oder für besondere Schalt- und Blitzfunktionen eingesetzt werden. SC-Ausführungen benötigen einen geeigneten Beleuchtungscontroller oder eine Stromquelle mit Strombegrenzung.

Specifications

Technical Specifications

01

General technical and commercial data

Design & Mechanics

Housing
Black anodized aluminum case
Weight
297 g

Supply & Output Power

Ambient Temperature
From -5 °C/+23°F up to +50 °C/+122°F
Versorgung
12 V – 24 V DC (min 11 V, max 26 V) at max. 6,5A
Compliance
CE, FCC, RoHS2

Channels, triggers & interfaces

Interface
Ethernet
Number of output channels
2
Flash current/channel
maximum 40 A per channel at 48 V
Continuous current/channel
4 A je Kanal at 24 V; maximum 5 A in total
Pulse width
1µs bis 60s (Auflösung 1µs)
02

Electrical characteristics

Model-dependent characteristics

In narrow view, the table can be shifted sideways.

variantElectrical characteristicsMeasured values and classification
variantChannelsSupply VoltageOutput voltageContinuous current (output)max. pulse currentPower consumption
HPSC2212 V – 24 V DC (min 11 V, max 26 V) at max. 6,5A48 V (pulsed/continuous)4 A je Kanal at 24 V; maximum 5 A in totalmaximum 40 A per channel at 48 VMax. 150 W (depending on load)

Notes on the specifications table

HPSC2

Operating modes: Continuous operation, external trigger, internal trigger, software trigger, external switching operation

Maximum output voltage: 48 V (strobe and continuous operation)

Maximum pulse current: 40 A at 48 V (per channel)

Current resolution: up to 1 mA

Maximum continuous current: 4 A at 24 V (per channel) up to 5 A at 24 V (total)

Pulse duration: 1 µs – 60 s, resolution 1 µs

Maximum frequency with external trigger: 50 kHz

Maximum frequency with internal trigger / external switching operation: 25 kHz

Trigger input: Optically isolated, high level at 3 V – 24 V; positive or negative edge

Trigger output: Optically isolated, max. 30 V / 50 mA

Interfaces: Ethernet (10Base-T/100Base-TX) RS-232 or USB1.x/2.0 on request

Supply: 12 V – 24 V DC (min. 11 V, max. 26 V) at max. 6,5 A

Power consumption: Max. 150 W (load-dependent)

Dimensions (H × W × L): 39 x 88 x 103 mm

03

Connection and PIN assignment

Phoenix Contact MSTB 2,5/3-ST-5,08 · Controller Supply

Controller supply · Phoenix Contact MSTB 2,5/3-ST-5,08

Connector drawing

Connector layout according to original manual

PINFarbeWire colorFunction
+––Power Supply +12 to 24V DC
-––Power GND
PE––Protective Earth

Terminal designations as per original; no additional numeric PIN numbers derived.

RJ45 · Ethernet · Configuration

Ethernet · Configuration · RJ45

Connector drawing

Connector layout according to original manual

PINFarbeWire colorFunction
1––TX+
2––TX-
3––RX+
6––RX-

The original lists these four contacts for Ethernet. Other contacts are not added as unassigned.

USB-B · USB · Configuration, if available

USB · Configuration, if available · USB-B

Connector drawing

USB-B pinout according to original manual

PINFarbeWire colorFunction
1––V+
2––D-
3––D+
4––V-

Applies exclusively to device versions with a USB interface. USB 1.x/2.0, cable type A to B; virtual serial COM port according to manual.

D-Sub 9-pin · RS232 · Configuration

RS232 · Configuration · D-Sub 9-pin

Connector drawing

Connector layout according to original manual

PINFarbeWire colorFunction
2––TxD on controller → RxD on PC
3––RxD at controller ← TxD at PC
5––GND
4 ↔ 6––Handshaking loop back
7 ↔ 8––Handshaking loop back
1, 9––Not connected

Note the controller side. In the original, the signal names of the PC side are also compared.

Phoenix Contact MSTB 2,5/4-ST-5,08 · HPSC2 · Trigger Input

2-kanalig · HPSC2 · Trigger-Eingang · Phoenix Contact MSTB 2,5/4-ST-5,08

Connector drawing

Model columns according to original manual

PINFarbeWire colorFunction
TRG1 +––Trigger Channel 1 +
TRG2 +––Trigger Channel 2 +
TRG1 -––Trigger Channel 1 -
TRG2 -––Trigger Channel 2 -

HIGH: >3VDC; LOW: 0–1,4VDC; recommended 0–24VDC; absolute limit 30VDC. Current per input 6–10mA (manual page 12). Image shows multiple models; note appropriate column.

Phoenix Contact MSTB 2,5/4-ST-5,08 · HPSC2 · LED Output

2-kanalig · HPSC2 · LED-Ausgang · Phoenix Contact MSTB 2,5/4-ST-5,08

Connector drawing

Model columns according to original manual

PINFarbeWire colorFunction
LED1 +––LED Power Output 1 + (common for all channels)
LED2 +––LED Power Output 2 + (common for all channels)
LED1 -––LED Power Output 1 -
LED2 -––LED Power Output 2 -

Terminal designations from the respective model column; no additional numeric assignment derived. HPSC2: Illustration shows LED and trigger output terminals together.

Phoenix Contact MSTB 2,5/4-ST-5,08 · HPSC2 · Trigger Output

2-kanalig · HPSC2 · Trigger-Ausgang · Phoenix Contact MSTB 2,5/4-ST-5,08

Connector drawing

Model columns according to original manual

PINFarbeWire colorFunction
OUT1 +––Trigger Output 1 +
OUT2 +––Trigger Output 2 +
OUT1 -––Trigger Output 1 -
OUT2 -––Trigger Output 2 -

Terminal designations from the respective model column; no additional numeric assignment derived. HPSC2: Illustration shows LED and trigger output terminals together. Trigger output: open collector, max. 30V / 50mA. Note different circuits for HPSC1 and HPSC1 f2/HPSC2/HPSC4 on pages 15/16.

04

Dimensional drawing

Dimensional drawing HPSC2 – HPSC2
Dimensions in mm.
05

Operating instructions

To maintain the optimal operating temperature, mount the device on a metal surface. Heat generation depends on the set output parameters.

Do not disassemble the device; sensitive components as well as high voltages and loads can cause damage and health hazards.

Do not expose to rain or moisture. The device is not intended for wet environments. Handle with care and do not throw.

Operate only with a power supply and within the limits specified on the respective controller and in its documentation.

Never connect or disconnect LED lighting while the power output is active. Always turn off the controller before changing the lighting.

06

Connection and control

Connection and control

Connection and control – HPSC2
Connection and control – HPSC2
Connection and control – HPSC2
Connection and control – HPSC2
Connection and control – HPSC2
Connection and control – HPSC2
Connection and control – HPSC2
Connection and control – HPSC2
Connection and control – HPSC2
Connection and control – HPSC2
Connection and control – HPSC2
Connection and control – HPSC2
Connection and control – HPSC2
Connection and control – HPSC2
Connection and control – HPSC2
Connection and control – HPSC2
Connection and control – HPSC2
Connection and control – HPSC2
Connection and control – HPSC2
Connection and control – HPSC2
Connection and control – HPSC2
Connection and control – HPSC2

Product inquiry

HPSC2 check for your application

Briefly describe your Prüfaufgabe.

Product: HPSC2

PDF Datasheet · Version 4.0

Select datasheet

HPSC2

Scope of the Data Sheet

The datasheet opens in a new tab. You can save it there as a PDF.