
Beleuchtungscontroller / Blitzsteuerung
HPSC2
- Schnittstelle: Ethernet
- Anzahl Ausgangskanäle: 2
- Blitzstrom/Kanal: maximal 40 A je Kanal bei 48 V
- Dauerstrom/Kanal: 4 A je Kanal bei 24 V; maximal 5 A insgesamt
- Pulsweite: 1µs bis 60s (Auflösung 1µs)
Bei 24-VDC-Ausführungen ist für den Dauerbetrieb kein Beleuchtungscontroller erforderlich. Ein Controller kann optional zur Helligkeitsregelung oder für besondere Schalt- und Blitzfunktionen eingesetzt werden. SC-Ausführungen benötigen einen geeigneten Beleuchtungscontroller oder eine Stromquelle mit Strombegrenzung.
Specifications
Technical Specifications
General technical and commercial data
Design & Mechanics
- Housing
- Black anodized aluminum case
- Weight
- 297 g
Supply & Output Power
- Ambient Temperature
- From -5 °C/+23°F up to +50 °C/+122°F
- Versorgung
- 12 V – 24 V DC (min 11 V, max 26 V) at max. 6,5A
- Compliance
- CE, FCC, RoHS2
Channels, triggers & interfaces
- Interface
- Ethernet
- Number of output channels
- 2
- Flash current/channel
- maximum 40 A per channel at 48 V
- Continuous current/channel
- 4 A je Kanal at 24 V; maximum 5 A in total
- Pulse width
- 1µs bis 60s (Auflösung 1µs)
Electrical characteristics
Model-dependent characteristics
In narrow view, the table can be shifted sideways.
| variant | Electrical characteristics | Measured values and classification | ||||
|---|---|---|---|---|---|---|
| variant | Channels | Supply Voltage | Output voltage | Continuous current (output) | max. pulse current | Power consumption |
| HPSC2 | 2 | 12 V – 24 V DC (min 11 V, max 26 V) at max. 6,5A | 48 V (pulsed/continuous) | 4 A je Kanal at 24 V; maximum 5 A in total | maximum 40 A per channel at 48 V | Max. 150 W (depending on load) |
No version matches these filters.
Notes on the specifications table
HPSC2
Operating modes: Continuous operation, external trigger, internal trigger, software trigger, external switching operation
Maximum output voltage: 48 V (strobe and continuous operation)
Maximum pulse current: 40 A at 48 V (per channel)
Current resolution: up to 1 mA
Maximum continuous current: 4 A at 24 V (per channel) up to 5 A at 24 V (total)
Pulse duration: 1 µs – 60 s, resolution 1 µs
Maximum frequency with external trigger: 50 kHz
Maximum frequency with internal trigger / external switching operation: 25 kHz
Trigger input: Optically isolated, high level at 3 V – 24 V; positive or negative edge
Trigger output: Optically isolated, max. 30 V / 50 mA
Interfaces: Ethernet (10Base-T/100Base-TX) RS-232 or USB1.x/2.0 on request
Supply: 12 V – 24 V DC (min. 11 V, max. 26 V) at max. 6,5 A
Power consumption: Max. 150 W (load-dependent)
Dimensions (H × W × L): 39 x 88 x 103 mm
Connection and PIN assignment
Phoenix Contact MSTB 2,5/3-ST-5,08 · Controller Supply
Controller supply · Phoenix Contact MSTB 2,5/3-ST-5,08

Connector layout according to original manual
| PIN | Farbe | Wire color | Function |
|---|---|---|---|
| + | – | – | Power Supply +12 to 24V DC |
| - | – | – | Power GND |
| PE | – | – | Protective Earth |
Terminal designations as per original; no additional numeric PIN numbers derived.
RJ45 · Ethernet · Configuration
Ethernet · Configuration · RJ45

Connector layout according to original manual
| PIN | Farbe | Wire color | Function |
|---|---|---|---|
| 1 | – | – | TX+ |
| 2 | – | – | TX- |
| 3 | – | – | RX+ |
| 6 | – | – | RX- |
The original lists these four contacts for Ethernet. Other contacts are not added as unassigned.
USB-B · USB · Configuration, if available
USB · Configuration, if available · USB-B

USB-B pinout according to original manual
| PIN | Farbe | Wire color | Function |
|---|---|---|---|
| 1 | – | – | V+ |
| 2 | – | – | D- |
| 3 | – | – | D+ |
| 4 | – | – | V- |
Applies exclusively to device versions with a USB interface. USB 1.x/2.0, cable type A to B; virtual serial COM port according to manual.
D-Sub 9-pin · RS232 · Configuration
RS232 · Configuration · D-Sub 9-pin

Connector layout according to original manual
| PIN | Farbe | Wire color | Function |
|---|---|---|---|
| 2 | – | – | TxD on controller → RxD on PC |
| 3 | – | – | RxD at controller ← TxD at PC |
| 5 | – | – | GND |
| 4 ↔ 6 | – | – | Handshaking loop back |
| 7 ↔ 8 | – | – | Handshaking loop back |
| 1, 9 | – | – | Not connected |
Note the controller side. In the original, the signal names of the PC side are also compared.
Phoenix Contact MSTB 2,5/4-ST-5,08 · HPSC2 · Trigger Input
2-kanalig · HPSC2 · Trigger-Eingang · Phoenix Contact MSTB 2,5/4-ST-5,08

Model columns according to original manual
| PIN | Farbe | Wire color | Function |
|---|---|---|---|
| TRG1 + | – | – | Trigger Channel 1 + |
| TRG2 + | – | – | Trigger Channel 2 + |
| TRG1 - | – | – | Trigger Channel 1 - |
| TRG2 - | – | – | Trigger Channel 2 - |
HIGH: >3VDC; LOW: 0–1,4VDC; recommended 0–24VDC; absolute limit 30VDC. Current per input 6–10mA (manual page 12). Image shows multiple models; note appropriate column.
Phoenix Contact MSTB 2,5/4-ST-5,08 · HPSC2 · LED Output
2-kanalig · HPSC2 · LED-Ausgang · Phoenix Contact MSTB 2,5/4-ST-5,08

Model columns according to original manual
| PIN | Farbe | Wire color | Function |
|---|---|---|---|
| LED1 + | – | – | LED Power Output 1 + (common for all channels) |
| LED2 + | – | – | LED Power Output 2 + (common for all channels) |
| LED1 - | – | – | LED Power Output 1 - |
| LED2 - | – | – | LED Power Output 2 - |
Terminal designations from the respective model column; no additional numeric assignment derived. HPSC2: Illustration shows LED and trigger output terminals together.
Phoenix Contact MSTB 2,5/4-ST-5,08 · HPSC2 · Trigger Output
2-kanalig · HPSC2 · Trigger-Ausgang · Phoenix Contact MSTB 2,5/4-ST-5,08

Model columns according to original manual
| PIN | Farbe | Wire color | Function |
|---|---|---|---|
| OUT1 + | – | – | Trigger Output 1 + |
| OUT2 + | – | – | Trigger Output 2 + |
| OUT1 - | – | – | Trigger Output 1 - |
| OUT2 - | – | – | Trigger Output 2 - |
Terminal designations from the respective model column; no additional numeric assignment derived. HPSC2: Illustration shows LED and trigger output terminals together. Trigger output: open collector, max. 30V / 50mA. Note different circuits for HPSC1 and HPSC1 f2/HPSC2/HPSC4 on pages 15/16.
Dimensional drawing
Operating instructions
Connection and control
Custom inquiry
Select matching controller
Please specify your lighting, the required number of channels, operating mode, and the desired control. We will check the appropriate combination and prepare your quote.
CAD data for your planning
We would be pleased to support you with CAD data and information on the mechanical integration of your desired version.
Request CAD data →Documents & CAD
Downloads
Bitte melden Sie sich mit Ihrem freigeschalteten Kundenkonto an.
Anmelden / RegistrierenIhre Kundenpreise sind freigeschaltet. Ihr hinterlegter Rabatt ist bereits berücksichtigt.
Open original price list (without customer discount)Product inquiry
HPSC2 check for your application
Briefly describe your Prüfaufgabe.






















I-CON
IPSC4