RONDO-C

Ringbeleuchtungen

RONDO-C

  • Außen-/Innendurchmesser: ca. 48 / 22,5 mm
  • Montage: C-Mount
  • Eigenschaft: kurzer Fokus
Inquire about product →Datasheet as PDF →

Specifications

Technical Specifications

01

General technical and commercial data

Design & Mechanics

Outer/inner diameter
approx. 48 / 22,5 mm
Mounting
C-Mount
Housing
Aluminum, black or natural anodized
Weight
approx. 55 g
LEDs
16
Diffuser
PMMA

Additional Technical Specifications

Property
short focus

Operation & Connection

Filter thread connection
C-Mount
Ambient Temperature
max. 50 °C recommended
Protection class (IP)
depending on version
Connection
M8 connector 4-pin on pigtail 10 cm
Versorgung
24 VDC or 12 VDC type; SC-Typ with controller
electrical protection class
III, safety extra-low voltage operation
Versorgung
24 VDC type: 24 VDC SC-Typ: For use with a Beleuchtungscontroller
Compliance
CE, RoHS
service life
The service life of LEDs is in the range of several 10.000 to 100.000 hours and is generally very high, but depends on many different factors such as ambient temperature, current load, etc.
Service life explained in WikiLED →
02

Model-dependent characteristics

Model-dependent characteristics

In narrow view, the table can be shifted sideways.

variantCurrent and flash operationMeasured values and classification
Light colourWavelength / Color Temperaturenm / KBeam angleLED · °Current consumption24VDC type / max. Konstantstrom SC-TypApproximate valuesIrradianceW/m² at constant currentApproximate values · Measurement directly on the diffuserElectrical powerWRisk groupEN 62471
Red625 nm15°30 mA330 W/m²1 Wexempt group
White–15°50 mA330 W/m²2 Wexempt group
Infrared850 nm6°–––exempt group
Infrared850 nm16°–––exempt group
Green–°–––exempt group
RGB – Red–120°–––exempt group
RGB – Green–120°–––exempt group
RGB – Blue–120°–––exempt group

Notes on the specifications table

Pulse current: Pulse duration t_on < 1 ms, duty cycle 1:10.

The pulse current specifications depend on the flash conditions.

Additional light colors and versions from UV to infrared available upon request.

03

Connection and PIN assignment

M8 Connector 4-pin · 24VDC · 1-channel

Connector drawing
PINFarbeWire colorFunction
1brownbrown+ 24V
3blueblue-

M8 Connector 4-pin · SC · 1-channel

Connector drawing
PINFarbeWire colorFunction
4blackblack+
3blueblue-

M8 Connector 4-pin · 24VDC with switching input · 1-channel

Connector drawing

Front view of housing

PINFarbeWire colorFunction
1brownbrown+ 24V
3blueblue-
4blackblackSwitching input*

* ON: 3,7V (~3mA) - 24V (~30mA) / OFF: < 3,0V

04

Dimensional drawing

Dimensional drawing RONDO-C
05

Operating instructions

Areas of application

This version is designed for continuous operation at 24VDC.

Operating modes

  • DC operation on a suitable power supply with 24VDC
  • switched operation on a suitable power supply via e.g. PLC, opto-relay
  • switched operation on a lighting controller (e.g. IPSC/HPSC or Gardasoft) in conjunction with a suitable power supply
  • brightness-controlled operation via lighting controller (IPSC/HPSC or Gardasoft) in conjunction with a suitable power supply

Flash operation

Flash operation via controller (e.g., IPSC/HPSC or Gardasoft) in conjunction with a suitable power supply. Depending on the lighting controller used and the maximum available output/flash voltage, the flash current in this combination can be increased by a maximum factor of 2 to 3 in order to remain within the permitted voltage range of the output/flash voltage of max. 50V.

Current limits

The maximum permissible currents for continuous and flash operation are also specified on the product label of the respective lighting.

Areas of application

This low-resistance version, optimized for flash operation, can also be used for switched, brightness-controlled, and continuous operation.

Required supply

One of the following power supplies is required for operation:

  • a lighting controller, e.g. from the IPSC/HPSC series, from Gefasoft or Gardasoft, or
  • a current source with current limiting.

Flash operation

Due to its low-resistance design, the SC version is particularly suitable for maximum current in flash operation. Compared to the 24-VDC types, output or flash voltages in the usual range up to a maximum of 50 V can be used.

As a result, the maximum flash current is typically significantly above the factor 2–3.

Current limits

The maximum permissible currents for continuous and flash operation are also specified on the product label of the respective lighting.

06

Application, light guidance, and optics

Application and light guidance

Application and light guidance – RONDO-C

Product inquiry

RONDO-C check for your application

Briefly describe your Prüfaufgabe.

Product: RONDO-C

PDF Datasheet · Version 4.0

Select datasheet

RONDO-C

Scope of the Data Sheet

The datasheet opens in a new tab. You can save it there as a PDF.