
Beleuchtungscontroller / Blitzsteuerung
IPSC4
- Schnittstelle: Ethernet, RS232
- Anzahl Ausgangskanäle: 4
- Blitzstrom/Kanal: je max. 10A @ 200V
- Dauerstrom/Kanal: je max. 1A @ 30V
- optional konfektionierte Kabelsätze
Bei 24-VDC-Ausführungen ist für den Dauerbetrieb kein Beleuchtungscontroller erforderlich. Ein Controller kann optional zur Helligkeitsregelung oder für besondere Schalt- und Blitzfunktionen eingesetzt werden. SC-Ausführungen benötigen einen geeigneten Beleuchtungscontroller oder eine Stromquelle mit Strombegrenzung.
Specifications
Technical Specifications
General technical and commercial data
Design & Mechanics
- Housing
- Black aluminum case
- Weight
- approx. 680 g
Supply & Output Power
- Ambient Temperature
- from -5 °C/+23°F up to +50 °C/+122°F
- Versorgung
- 12 V – 24 V DC (min 11 V, max 26 V)
- Compliance
- CE, RoHS2
Channels, triggers & interfaces
- Interface
- Ethernet, RS232
- Number of output channels
- 4
- Flash current/channel
- max. 10A each @ 200V
- Continuous current/channel
- max. 1A each @ 30V
Electrical characteristics
Model-dependent characteristics
In narrow view, the table can be shifted sideways.
| variant | Electrical characteristics | Measured values and classification | ||||
|---|---|---|---|---|---|---|
| variant | Channels | Supply Voltage | Output voltage | Continuous current (output) | max. pulse current | Power consumption |
| IPSC4 | 4 | 12 V – 24 V DC (min 11 V, max 26 V) | 200 V (pulsed) 55 V (continuous) | 1A @ 30 V per channel (4A total) | 10A @ 200 V per channel (40A total) | Max 5A @ 24 V (120 W) |
No version matches these filters.
Notes on the specifications table
IPSC4
Operating modes: Continuous operation, external trigger, internal trigger, software trigger, external switching operation
Maximum output voltage: 200 V (strobe operation) 55 V (continuous operation)
Maximum pulse current (depending on pulse duration): 10 A at 200 V per channel (40 A total)
Maximum continuous current: 1 A at 30 V per channel (4 A total)
Pulse duration: 1 µs – 1000 ms in steps of 1 µs
Maximum frequency with external trigger: 4,9 kHz
Maximum frequency with internal trigger / external switching operation: 997 Hz
Interfaces: Ethernet (10BaseT), RS232
Supply: 12 V – 24 V DC (min. 11 V, max. 26 V)
Power consumption: max. 5 A at 24 V (120 W)
Dimensions (H × W × L): 55 x 130 x 124 mm
Connection and PIN assignment
Phoenix Contact MSTB 2,5/3-ST-5,08 · Controller Supply
Controller supply · Phoenix Contact MSTB 2,5/3-ST-5,08

Connector layout according to original manual
| PIN | Farbe | Wire color | Function |
|---|---|---|---|
| + | – | – | Power Supply +12 to 24V DC |
| - | – | – | Power GND |
| PE | – | – | Protective Earth |
Terminal designations as per original; no additional numeric PIN numbers derived.
RJ45 · Ethernet · Configuration
Ethernet · Configuration · RJ45

Connector layout according to original manual
| PIN | Farbe | Wire color | Function |
|---|---|---|---|
| 1 | – | – | TX+ |
| 2 | – | – | TX- |
| 3 | – | – | RX+ |
| 6 | – | – | RX- |
The original lists these four contacts for Ethernet. Other contacts are not added as unassigned.
USB-B · USB · Configuration, if available
USB · Configuration, if available · USB-B

USB-B pinout according to original manual
| PIN | Farbe | Wire color | Function |
|---|---|---|---|
| 1 | – | – | V+ |
| 2 | – | – | D- |
| 3 | – | – | D+ |
| 4 | – | – | V- |
Applies exclusively to device versions with a USB interface. USB 1.x/2.0, cable type A to B; virtual serial COM port according to manual.
D-Sub 9-pin · RS232 · Configuration
RS232 · Configuration · D-Sub 9-pin

Connector layout according to original manual
| PIN | Farbe | Wire color | Function |
|---|---|---|---|
| 2 | – | – | TxD on controller → RxD on PC |
| 3 | – | – | RxD at controller ← TxD at PC |
| 5 | – | – | GND |
| 4 ↔ 6 | – | – | Handshaking loop back |
| 7 ↔ 8 | – | – | Handshaking loop back |
| 1, 9 | – | – | Not connected |
Note the controller side. In the original, the signal names of the PC side are also compared.
Deltron DT13W3 · IPSC4 · LED output
4-kanalig · IPSC4 · LED-Ausgang · Deltron DT13W3

Model columns according to original manual
| PIN | Farbe | Wire color | Function |
|---|---|---|---|
| 1 | – | – | CH1-, Channel 1 - |
| 2 | – | – | CH2-, Channel 2 - |
| 3 | – | – | CH3-, Channel 3 - |
| 4 | – | – | CH4-, Channel 4 - |
| 5 | – | – | Not assigned |
| 6 | – | – | Not assigned |
| 7 | – | – | Analog ID |
| 8 | – | – | Signal GND (for signals 7, 9 and 10) |
| 9 | – | – | Trigger Output Digital Signal, 3,3V LVTTL |
| 10 | – | – | Digital ID (1-wire EEPROM), 3,3V LVTTL |
| A1 | – | – | 12–24V DC je nach Versorgung, max. 0,5A für Lüfter |
| A2 | – | – | Power GND |
| A3 | – | – | V+, Common Output Voltage |
Signal GND and Power GND are labeled separately. Original image contains three model columns; observe the appropriate column.
Phoenix Contact MSTB 2,5/6-ST-5,08 / BNC Trigger 1 · IPSC4 · Trigger Input
4-channel · IPSC4 · trigger input · Phoenix Contact MSTB 2,5/6-ST-5,08 / BNC trigger 1

Model columns according to original manual
| PIN | Farbe | Wire color | Function |
|---|---|---|---|
| 1 | – | – | Trigger Channel 1 + |
| 2 | – | – | Trigger Channel 2 + |
| 3 | – | – | Trigger Channel 3 + |
| 4 | – | – | Trigger Channel 4 + |
| - | – | – | Common Trigger GND |
| BNC + | – | – | Trigger Input 1 + |
| BNC - | – | – | Common Trigger GND |
HIGH: +3 to +24V DC; LOW: 0 to +0,5V DC; undefined: +0,5 to +3V DC. Common trigger ground; note terminal order in original image.
Dimensional drawing
Operating instructions
Connection and control
Custom inquiry
Select matching controller
Please specify your lighting, the required number of channels, operating mode, and the desired control. We will check the appropriate combination and prepare your quote.
Kabelsätze nach Maß
Die passende Verbindung.
Configure the matching cable set for your IPSC4. Add matching items and custom designs directly to your inquiry cart.
Aus unserem Zubehörangebot
Passende Artikel
Hinweise zur Auswahl und Dokumentation
Ein Kabelsatzcode mit „SC-“ ist nicht gleichbedeutend mit einer SC-Leuchte. 12/24-V-, SC-/6-V-Ausführungen und universelle Verlängerungen werden getrennt betrachtet. M12 bezeichnet hier ausschließlich den gewählten 4-poligen Anschluss mit A-Codierung.
Ein 24-VDC-Typ benötigt für den Dauerbetrieb keinen zwingenden Beleuchtungscontroller. Für SC-Ausführungen gelten die freigegebenen Betriebsbedingungen und die erforderliche Strombegrenzung. Die passende Anschlussbelegung richtet sich immer nach der konkreten Ausführung.
Die belegten Controllerkanäle ergeben sich aus der Anzahl der Abgänge × Kanäle je Abgang. IPSC1 stellt einen, IPSC2 zwei und IPSC4 vier Kanäle bereit. Einzelne Controllerkanäle dürfen frei bleiben.
Grundlagen: Kabelsatz-Bestellinformation für IPSC-Controller V1.1 und zugehörige dokumentierte Anschlussbeispiele. Individuelle Ausführungen werden bei der Angebotserstellung geprüft.
Documents & CAD
Downloads
Bitte melden Sie sich mit Ihrem freigeschalteten Kundenkonto an.
Anmelden / RegistrierenIhre Kundenpreise sind freigeschaltet. Ihr hinterlegter Rabatt ist bereits berücksichtigt.
Open original price list (without customer discount)Product inquiry
IPSC4 check for your application
Briefly describe your Prüfaufgabe.




























I-CON
IPSC1